Can I Set Up a Tub Myself? Considerations And Also Steps
Can I Set Up a Tub Myself? Considerations And Also Steps
Blog Article
Are you currently in search of know-how about How to Install a Bathtub?
Installing a bath tub isn't specifically rocket science, but it does call for strong plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old tub with a brand-new one is also a reasonably hard task. If the old tub is readily easily accessible, the task can relocate quickly; if you need to open up a wall surface to eliminate the old tub and also place the new bathtub, the job is a lot harder. In either case, the project is within a residence handyman's skills, although you will require an assistant to move out the old bathtub as well as set in the brand-new one. Ensure you have certified yourself for the job and also are comfortable trying it. Instead of hiring a contractor to take over a halfway-completed task, it is much better to take into consideration utilizing one prior to you begin. Opportunities are you might need a specialist plumber to make tube connections.
This post will certainly aid you install a new tub in your bathroom if you have actually currently acquired a new bathtub as well as don't require to change the plan of your previous water supply pipes.
Your tools and also product checklist must comprise the following:
Planning for the Installation
Firstly, the supporting frame provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to see to it that if the tap comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the versatile faucet adapters to the bottom of both faucets using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of all of the provided washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its last setting.
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, after that the first thing you must do is detach the supply of water. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic due to the limited gain access to that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the staying water that will certainly originate from the pipes. As soon as the supply pipes have been removed, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Prior to proceeding to fit the brand-new faucets, contrast the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Mounting the Bath tub
Using both wood boards under its feet, place the bathtub in the needed placement. The wooden boards are valuable in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and adjusting the feet on the tub up until the level reviews degree.
To install taps, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the supply of water as well as inspect all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill the bathtub and also check the overflow outlet and the regular outlet for leaks.
Lastly, take care of the bathroom paneling as described in the producer's instruction manual. Tiling as well as securing around the bath tub should wait until the bathtub has been utilized a minimum of when as this will certainly resolve it right into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washers are in location between the tap and also the sink. Safeguard the tap in place with the manufacturer given backnut. As soon as the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former kind needs to be linked to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack a stiff seal, causing the water to pass through the wall in between the bathroom and the tiling, bring about problems with wetness as well as possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, as well as are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched paper or soft rope. Remember to constantly load the bathtub with water before securing, to permit the movement experienced when the tub remains in usage. The sealant can break relatively very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently available on the market. It is a good idea to fit the floor tiles utilizing waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am very inquisitive about How to Install a Bathtub and I hope you liked our page. Loved our posting? Please share it. Help other people find it. Thanks a bunch for your time. Visit us again soon.
Estimate Free
Report this page